tool:vinyl_cutter
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
tool:vinyl_cutter [2017/08/24 06:02] – fixed link to vendor knowledge base. also quoted info on blade angle directly in wiki, since vendor site is atrocious mimi_x | tool:vinyl_cutter [2021/04/26 14:21] (current) – Added my findings on pressure nich | ||
---|---|---|---|
Line 26: | Line 26: | ||
Vectors, the preferred format for the cutter, are usually created by software such as Adobe Illustrator, | Vectors, the preferred format for the cutter, are usually created by software such as Adobe Illustrator, | ||
- | I (@lefty) have had the best luck importing PSD (Photoshop) vectors as .psd files. | + | I (@lefty) have had the best luck importing PSD (Photoshop) vectors as .psd files. |
To import a vector, create a new job with File -> New, then File -> Import. Pick the vector file you'd like to import, and check that it shows up in the Preview window. | To import a vector, create a new job with File -> New, then File -> Import. Pick the vector file you'd like to import, and check that it shows up in the Preview window. | ||
Line 46: | Line 46: | ||
- First release the two pinch rollers at the back of the machine by pulling the levers up. | - First release the two pinch rollers at the back of the machine by pulling the levers up. | ||
- Move the material freely through the machine and also move the rollers from side-to-side depending on the position and size of the vinyl stock. | - Move the material freely through the machine and also move the rollers from side-to-side depending on the position and size of the vinyl stock. | ||
- | - Once it is positioned and aligned, push the levers down to engage the pinch rollers and lock everything in place. | + | - Once it is positioned and aligned, push the levers down to engage the pinch rollers and lock everything in place. This also sets the boundaries of your cutting area, so be sure to set the locking rollers beyond your cut job but still moving the vinyl. Try not to push the vinyl too close to the edges, as it will tend to bind up and cause skewed cuts. |
- Send your cut job | - Send your cut job | ||
- In VectorCut, click "Send Cut Job" and wait a few seconds. Be careful to not click this button multiple times, or you will queue multiple cut jobs to the cutter. | - In VectorCut, click "Send Cut Job" and wait a few seconds. Be careful to not click this button multiple times, or you will queue multiple cut jobs to the cutter. | ||
Line 56: | Line 56: | ||
Chances are the blade is dull and you won't get a very good cut. To replace the blade, open the bracket on the traveling cut head and remove the cylindrical part. Unscrew the top to get at the blade. Don't lose any of these parts! | Chances are the blade is dull and you won't get a very good cut. To replace the blade, open the bracket on the traveling cut head and remove the cylindrical part. Unscrew the top to get at the blade. Don't lose any of these parts! | ||
- | Searching AliExpress or eBay for " | + | We now have two different |
+ | |||
+ | Since the 2mm blades are much more common and easier to come by, there is almost no reason to use the 2,5 mm holder. | ||
+ | |||
- | Common blades are 2mm diameter but our blade holder requires 2.5mm blades. A 2mm will sort of work, but with significant slop. | ||
=== Blade Angle === | === Blade Angle === | ||
- | According | + | According |
<WRAP center round box 85%> | <WRAP center round box 85%> | ||
Line 82: | Line 85: | ||
+ | ==== A visual step-by-step ==== | ||
+ | Once you've imported your file according to the steps above,the first thing you'll want to do is to set up your Working Area to understand how your artwork fits on your material. | ||
+ | **1.Working Area** | ||
+ | To do this go to Settings > Working Area on the top menu panel.Once in the pop-out window you can adjust the width and height of the Working area to the required size. | ||
+ | {{: | ||
- | ==== More info ==== | + | **2.Resizing** |
+ | Generally you might need to resize and reposition your artwork. You can do this in the parameters window, see image below. | ||
- | | + | {{: |
+ | |||
+ | **3.Artwork positioning** | ||
+ | The actual position of your artwork relative to the working area doesn' | ||
+ | File> | ||
+ | |||
+ | {{: | ||
+ | {{: | ||
+ | {{: | ||
+ | |||
+ | **4.Output** | ||
+ | Once you're happy with how the preview looks you're almost ready to get cutting. First you need to check some of the parameters. File> | ||
+ | |||
+ | -Pressure - I recommend 250-275 (thicker material may need more). | ||
+ | Nich's Update: I tested with 250 and cut right through, and found that for the material I found in the scraps bin, 75 was about right, though there was a small bit of bunching on tight corners. | ||
+ | |||
+ | -Speed - 5cm/s (slow down further if you have intricate cuts) | ||
+ | |||
+ | -Material - Width & Length, this is important as if you don't set it large enough, the program will cute up some of your design thinking you need to add a new material roll. | ||
+ | |||
+ | -Weed Box - this will cut an offset box around your artwork, depends on whether you want to save material or not. | ||
+ | |||
+ | **5.Cutting** | ||
+ | Turn the machine on (it will run some automatic calibrations). | ||
+ | Slide the material from the back of the machine under the rollers and past the blade point. | ||
+ | Lock down the two rollers at the back to keep the material in place. | ||
+ | Using the arrows, manoeuvre the cutter head to the starting point of your choice on the material. | ||
+ | Push the Sizing Origin Set button on the machine to set that as the origin (zero) point. | ||
+ | Click Output on GreatCut and the program will run. | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ==== More info ==== | ||
+ | |
tool/vinyl_cutter.1503554575.txt.gz · Last modified: 2017/08/24 06:02 by mimi_x