User Tools

Site Tools


tool:vinyl_cutter

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
tool:vinyl_cutter [2017/05/27 23:45] – Fleshed out the software usage instructions a bit leftytool:vinyl_cutter [2021/04/26 14:21] (current) – Added my findings on pressure nich
Line 26: Line 26:
 Vectors, the preferred format for the cutter, are usually created by software such as Adobe Illustrator, Adobe Photoshop, or The GIMP (which is free software, and pretty good). Vectors, the preferred format for the cutter, are usually created by software such as Adobe Illustrator, Adobe Photoshop, or The GIMP (which is free software, and pretty good).
  
-I (@lefty) have had the best luck importing PSD (Photoshop) vectors as .psd files.  These seem to translate well into the software without a lot of extra tweaking.  EPS files will work, but GreatCut tends to choke on the objects sometimes - missing lines and strange cuts, etc.   Solid shapes tend to work best, as the cutter can just cut the outside of the shape, but it will entirely depend on the final result you'd like.+I (@lefty) have had the best luck importing PSD (Photoshop) vectors as .psd files.  These seem to translate well into the software without a lot of extra tweaking.  .EPS and .AI files will work, but GreatCut tends to choke on the objects sometimes - missing lines and strange cuts, etc.   Solid shapes tend to work best, as the cutter can just cut the outside of the shape, but it will entirely depend on the final result you'd like.
  
 To import a vector, create a new job with File -> New, then File -> Import. Pick the vector file you'd like to import, and check that it shows up in the Preview window.  GreatCut is a bit finicky on the formats it will successfully import, but if it shows up in the preview, it should import successfully. To import a vector, create a new job with File -> New, then File -> Import. Pick the vector file you'd like to import, and check that it shows up in the Preview window.  GreatCut is a bit finicky on the formats it will successfully import, but if it shows up in the preview, it should import successfully.
Line 46: Line 46:
     - First release the two pinch rollers at the back of the machine by pulling the levers up.      - First release the two pinch rollers at the back of the machine by pulling the levers up. 
     - Move the material freely through the machine and also move the rollers from side-to-side depending on the position and size of the vinyl stock.      - Move the material freely through the machine and also move the rollers from side-to-side depending on the position and size of the vinyl stock. 
-    - Once it is positioned and aligned, push the levers down to engage the pinch rollers and lock everything in place.  Try not to push the vinyl too close to the edges, as it will tend to bind up and cause skewed cuts.+    - Once it is positioned and aligned, push the levers down to engage the pinch rollers and lock everything in place. This also sets the boundaries of your cutting area, so be sure to set the locking rollers beyond your cut job but still moving the vinyl.  Try not to push the vinyl too close to the edges, as it will tend to bind up and cause skewed cuts.
   - Send your cut job   - Send your cut job
     - In VectorCut, click "Send Cut Job" and wait a few seconds. Be careful to not click this button multiple times, or you will queue multiple cut jobs to the cutter.      - In VectorCut, click "Send Cut Job" and wait a few seconds. Be careful to not click this button multiple times, or you will queue multiple cut jobs to the cutter. 
Line 56: Line 56:
 Chances are the blade is dull and you won't get a very good cut. To replace the blade, open the bracket on the traveling cut head and remove the cylindrical part. Unscrew the top to get at the blade. Don't lose any of these parts! Chances are the blade is dull and you won't get a very good cut. To replace the blade, open the bracket on the traveling cut head and remove the cylindrical part. Unscrew the top to get at the blade. Don't lose any of these parts!
  
-Searching AliExpress or eBay for "Roland GCC" will yield plenty of inexpensive blade options.+We now have two different blade holders, a darker one that holds 2.5mm diameter blades, and a silver one that holds 2mm diameter blades.
  
-Common blades are 2mm diameter but our blade holder requires 2.5mm bladesA 2mm will sort of workbut with significant slop.+Since the 2mm blades are much more common and easier to come by, there is almost no reason to use the 2,5 mm holder. 
 + 
 + 
 + 
 + 
 +=== Blade Angle === 
 + 
 +According to the knowledge base linked below: 
 +<WRAP center round box 85%> 
 + 
 +**Blade angle: 45 vs60 degree : ** Most vinyl materials have two layersa Release liner or “backing” and the vinyl itself. The cutter is designed to cut completely through the vinyl without cutting completely through the backing. When loading the material, the vinyl should be facing up. Establishing which side is up should be fairly straight forward with most materials. When cutting heat-transfer vinyl, the backing will be the shiny (glossy) side of the material. Place the clear plastic glossy side down when loading it into the cutter.
  
    
  
 +The primary reason for blades with different angles, is cutting depth. A lower angle (45 degree) is great for thin materials, while a steeper angle (60 degrees) has a more vertical cutting orientation that penetrates deeper. An increased amount of blade dragging through the material when cutting fine detail can cause, what they call, vinyl ears (parts lifted up). With minimal blade in the material, a 60 degree blade tends to cause fewer, if any, vinyl ears.
  
-==== More info ====+ 
  
-  * [[http://support.uscutter.com/index.php?/Knowledgebase/Article/View/135/24/25-vs-45-vs-60---what-blade-do-i-use|What blade angle to use]]+Using a 60 degree blade on everyday cutting is a waste of a blade, technically speakingLess of the blade's cutting area is used, and blade life is wastedThe more horizontal cutting orientation of the 45 degree blade accurately distributes the cutting task over a larger blade area, and thus last longer (and is cheaper). 
 + 
 +  
 + 
 +So use a 45 degree blade always, unless a 60 degree blade is needed for thick or more custom types of cutting, if 45 degrees blades are not available. 
 + 
 +</WRAP> 
 + 
 + 
 +==== A visual step-by-step ==== 
 +Once you've imported your file according to the steps above,the first thing you'll want to do is to set up your Working Area to understand how your artwork fits on your material.  
 + 
 +**1.Working Area** 
 +To do this go to Settings > Working Area on the top menu panel.Once in the pop-out window you can adjust the width and height of the Working area to the required size.  
 + 
 +{{:tool:2_workingarea.jpg?400|}} 
 + 
 +**2.Resizing** 
 +Generally you might need to resize and reposition your artwork. You can do this in the parameters window, see image below. 
 + 
 +{{:tool:4_resizing.jpg?400|}} 
 + 
 +**3.Artwork positioning** 
 +The actual position of your artwork relative to the working area doesn't have any bearing on the final output as the software relocates your artwork to the zero point before outputting. You can check the final position of your artwork in the Preview tool. This is a representation of what will be cut. 
 +File>Output>Preview  
 + 
 +{{:tool:5_location.jpg?400|}} 
 +{{:tool:6a_preview.jpg?400|}} 
 +{{:tool:6b_preview.jpg?400|}} 
 + 
 +**4.Output** 
 +Once you're happy with how the preview looks you're almost ready to get cutting. First you need to check some of the parameters. File>Output.  
 + 
 +-Pressure I recommend 250-275 (thicker material may need more).  
 +Nich's Update: I tested with 250 and cut right through, and found that for the material I found in the scraps bin, 75 was about right, though there was a small bit of bunching on tight corners.   
 + 
 +-Speed 5cm/s (slow down further if you have intricate cuts) 
 + 
 +-Material Width & Length, this is important as if you don't set it large enough, the program will cute up some of your design thinking you need to add a new material roll. 
 + 
 +-Weed Box - this will cut an offset box around your artwork, depends on whether you want to save material or not. 
 + 
 +**5.Cutting** 
 +Turn the machine on (it will run some automatic calibrations). 
 +Slide the material from the back of the machine under the rollers and past the blade point.  
 +Lock down the two rollers at the back to keep the material in place.  
 +Using the arrows, manoeuvre the cutter head to the starting point of your choice on the material.  
 +Push the Sizing Origin Set button on the machine to set that as the origin (zero) point.  
 +Click Output on GreatCut and the program will run. 
 + 
 + 
 +   
 + 
 + 
 + 
 +==== More info ==== 
 +  * [[http://www.uscuttersupport.com/kbpage.html|US Cutter Support Knowledge Base]].
tool/vinyl_cutter.1495928716.txt.gz · Last modified: 2017/05/27 23:45 by lefty

Except where otherwise noted, content on this wiki is licensed under the following license: Public Domain
Public Domain Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki