User Tools

Site Tools


tool:sherline_cnc_mill

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
tool:sherline_cnc_mill [2016/09/14 00:52] jarretttool:sherline_cnc_mill [2018/03/09 05:01] (current) – Added link to PCB milling with Sherline colorcoded
Line 11: Line 11:
 ^ Arrival Date       | June 2010                                                                   | ^ Arrival Date       | June 2010                                                                   |
 ^ Location           | Workshop                                      | ^ Location           | Workshop                                      |
-^ Value              | $2000                                                                     | 
 ^ Champion           | See [[tool:compendium_of_champions#tools|Compendium of Champions]]     | ^ Champion           | See [[tool:compendium_of_champions#tools|Compendium of Champions]]     |
 ====== Information: ====== ====== Information: ======
  
-Forum thread: https://talk.hackspace.ca/t/vhs-group-project-sherline-cnc-mill/2588+Forum thread: https://talk.vanhack.ca/t/vhs-group-project-sherline-cnc-mill/2588
  
 For regular mill's operation:\\ For regular mill's operation:\\
Line 32: Line 31:
 __Required:__ __Required:__
   * Safety Glasses   * Safety Glasses
-  * Clamping devices (apply https://talk.hackspace.ca/t/vhs-group-project-sherline-cnc-mill/2588 liberally; better to have more clamps at moderate pressure than few at great pressure, to avoid damaging the T-slot)+  * Clamping devices (apply https://talk.vanhack.ca/t/vhs-group-project-sherline-cnc-mill/2588 liberally; better to have more clamps at moderate pressure than few at great pressure, to avoid damaging the T-slot)
   * an experienced machine operator (if this is not you, you must get someone to help you!)   * an experienced machine operator (if this is not you, you must get someone to help you!)
   * long hair must be tied back   * long hair must be tied back
Line 76: Line 75:
   * Remove your tool(s) from the chuck.   * Remove your tool(s) from the chuck.
   * Clean up the cutting leftovers.  The next user thanks you!   * Clean up the cutting leftovers.  The next user thanks you!
 +
 +====== PCB Milling ======
 +
 +See [[PCB Milling With Sherline]].
  
 ====== Notes for later: ====== ====== Notes for later: ======
  
   - Machine zero, work zero and G28: https://www.youtube.com/watch?v=J3gN5wqz2FE   - Machine zero, work zero and G28: https://www.youtube.com/watch?v=J3gN5wqz2FE
-  - http://reprap.org/wiki/4_Axis_TB6560_CNC_Stepper_Motor_Driver_Board_Controller +  - http://reprap.org/wiki/4_Axis_TB6560_CNC_Stepper_Motor_Driver_Board_Controller 4 Axis TB6560 Controller board
-4 Axis TB6560 Controller board+
   - Tool speed calculator: http://zero-divide.net/?page=fswizard   - Tool speed calculator: http://zero-divide.net/?page=fswizard
   - We have collets for 3mm, 4mm, 6mm and 1/8”, 3/16”, 1/4" shank end mills.   - We have collets for 3mm, 4mm, 6mm and 1/8”, 3/16”, 1/4" shank end mills.
   - We have a [[http://www.atlas-machinery.com/step-block-hold-down-set/|step block hold down set]], a [[http://www.atlas-machinery.com/milling-vise/|milling vice]] and a set of extra [[http://www.atlas-machinery.com/t-nuts-10-32-10pc-set/|T-nuts]] to clamp your work.   - We have a [[http://www.atlas-machinery.com/step-block-hold-down-set/|step block hold down set]], a [[http://www.atlas-machinery.com/milling-vise/|milling vice]] and a set of extra [[http://www.atlas-machinery.com/t-nuts-10-32-10pc-set/|T-nuts]] to clamp your work.
   - The upper e-stop button should work, but verify that it stops the mill before you begin any real operation.   - The upper e-stop button should work, but verify that it stops the mill before you begin any real operation.
tool/sherline_cnc_mill.1473814374.txt.gz · Last modified: 2016/09/14 00:52 by jarrett

Except where otherwise noted, content on this wiki is licensed under the following license: Public Domain
Public Domain Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki