tool:laser_cutter:settings
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
tool:laser_cutter:settings [2019/10/17 04:49] – Increased speed for 1/8 ply from 16 to 24 tristan_lane | tool:laser_cutter:settings [2022/09/27 01:05] (current) – david_neufeld | ||
---|---|---|---|
Line 25: | Line 25: | ||
===== Plastics ===== | ===== Plastics ===== | ||
- | ^ Material ^ Mode ^ Speed ^ Power ^ Corner Power ^ Passes ^ Notes ^ | + | ^ Material ^ Mode ^ Speed ^ Power ^ Corner Power ^ Passes ^ Notes ^ |
| Acrylic - 1/ | | Acrylic - 1/ | ||
| Acrylic - 1/ | | Acrylic - 1/ | ||
- | | Polypropylene (0.75mm) | Cut | 30 | 50 | 45 | 1 | From Yoko-yaya, ideal for painting stencils (John) | | + | | Acrylic - 4.5mm | Cut | 23 | 50 | 50 | 1 | |
- | | EVA Foam (very thin, < 4mm) | Cut | | | | 1 | Michaels | | + | | Polypropylene (0.75mm) | Cut | 30 | 50 | 45 | 1 | From Yoko-yaya, ideal for painting stencils (John) | |
- | | EVA Foam (thin, ~1/ | + | | EVA Foam (very thin, < 4mm) | Cut | | | | 1 | Michaels | |
+ | | EVA Foam (thin, ~1/ | ||
| EVA Foam (thick, 1/2" floor mats) | Cut | 30 | 50 | 50 | 1 | Canadian Tire, Home Depot, etc. | | | EVA Foam (thick, 1/2" floor mats) | Cut | 30 | 50 | 50 | 1 | Canadian Tire, Home Depot, etc. | | ||
- | | PET/PETG (e.g. Mylar(tm) ) | Cut | | | | 1 | | | + | | PET/PETG (e.g. Mylar(tm) ) | Cut | | | | 1 | |
- | | Kapton Polyimide Film | | | | | | [[http:// | + | | PET/PETG (1/ |
+ | | Kapton Polyimide Film | | | | | | [[http:// | ||
| Styrene - 2mm | Cut | | | | 1 | 2mm white styrene sheet from hobby stores | | Styrene - 2mm | Cut | | | | 1 | 2mm white styrene sheet from hobby stores | ||
Line 39: | Line 41: | ||
^ Material ^ Mode ^ Speed ^ Power ^ Corner Power ^ Passes ^ Notes ^ | ^ Material ^ Mode ^ Speed ^ Power ^ Corner Power ^ Passes ^ Notes ^ | ||
| Leather (Vegetable Tanned) | Cut | | | | 1 | | | | Leather (Vegetable Tanned) | Cut | | | | 1 | | | ||
- | | Felt | Cut | | + | | Felt | Cut | |
===== Other ===== | ===== Other ===== | ||
Line 45: | Line 47: | ||
| Application Tape | | | | | | Small amounts used for masking | | | Application Tape | | | | | | Small amounts used for masking | | ||
| Painters Tape | | | | | | Small amounts used for masking | | | Painters Tape | | | | | | Small amounts used for masking | | ||
+ | | Laserbond100 Marking Spray | | | | | | Aerosol propellants are nasty - ensure the coating has fully dried before lasering | | ||
+ | | Cermark 6000 Marking Spray | | | | | | Aerosol propellants are nasty - ensure the coating has fully dried before lasering | | ||
+ | |||
===== Etch Only ===== | ===== Etch Only ===== | ||
Line 67: | Line 72: | ||
| Fiberglass | Hazardous dust | | | Fiberglass | Hazardous dust | | ||
| Printed Circuit board | Hazardous dust | | | Printed Circuit board | Hazardous dust | | ||
+ | | Chrome Tanned Leather | Toxic/ | ||
tool/laser_cutter/settings.1571287795.txt.gz · Last modified: 2019/10/17 04:49 by tristan_lane