Differences

This shows you the differences between two versions of the page.

--- tool:green_manual_mill [2017/01/18 16:12] – rsim
+++ tool:green_manual_mill [2020/03/16 07:23] – billiam
@@ Line 1: / Line 1: @@
 ====== Manual Mill ======
-^ Status             | Operational as of November 2013                           |
+^ Status             | Operational as of March 2020                           |
 ^ Training           | Required                                       |
 ^ Hackable           | NO                                                              |
-^ Usage Restrictions | Members Only                     |
+^ Usage Restrictions | Members Only, only after VHS training / orientation                     |
 ^ Owner              | (VHS or Name of proper owner)                                          |
-^ If it Breaks       | (Panic procedure, usually involving emailing list and "broken" sign)   |
+^ If it Breaks       | Attach "Out of Order" sign / note. Post to Talk and Slack, contact area Champions   |
 ^ Loan Status        | Temporary                  |
 ^ Arrival Date       | November 2013                                                                   |
-^ Location           | (Location within VHS, eg Workshop                                      |
+^ Location           | Machine Shop                                      |
 ^ Champion           | See [[tool:compendium_of_champions#tools|Compendium of Champions]]     |
-{{ ::green-manual-mill.jpg?200|}}
+{{ ::green-manual-mill.jpg?200| }}
 ===== Safety =====
-Always wear eye protection while using the mill. Do not use the mill if you do not know how to use this type of machine. If used improperly; workpieces of pieces of cutting tools can be thrown around the shop at high velocity.
+Always wear eye protection while using the mill. VHS-specific training / orientation is required. If used improperly, workpieces or pieces of cutting tools can be thrown around the shop at high velocity.
 ===== Specifications: Mill =====
-Mill is a Long Chang LC-15A. No specifications for this mill appear to be available online. The following information was measured from the mill and may be inaccurate.
+Mill is a Long Chang LC-15A. Very little info for this mill is available online.
+Please review this {{ :tool:lc15_lc30_manual.pdf | Basic Manual }}
+The following information was measured from the mill and may be inaccurate.
 Spindle Taper: Measured ~3.215in long, 0.8in minor diameter, 0.95in major diameter. Very close to Morse #3
@@ Line 27: / Line 31: @@
 ===== Notes =====
-To move mill head up and down (major vertical adjustment); you need to loosen two bolts on the right-hand-side of the head, and use the crank on the left-hand-side of the mill to raise or lower. Retighten securing bolts before use (when untightened, crank has huge slop).
+To move mill head up and down (major vertical adjustment); you need to loosen two nuts on the right-hand-side of the head, and use the crank on the left-hand-side of the mill to raise or lower. Retighten securing bolts before use (when loose, crank has huge slop).
 ===== Axes =====
@@ Line 37: / Line 41: @@
 ===== Fixtures =====
-We have a drilling vise intended for use with this mill that clamps to the mill table.
+The 3.5" swivel vise can be bolted to the table via T nuts / bolts. Never assume that the vise is aligned correctly; use a dial indicator to check.
 We have a set of 1/2in T nuts + fingers + step blocks for the CNC mill that will also fit this mill.
@@ Line 43: / Line 47: @@
 ===== Tooling =====
-- Drill Chuck
+- Drill Chuck - at the moment, the only chuck key that fits is on the drill press in the Fab shop area.
+- 2x Offset boring heads
+- Fly cutter. Takes an HSS toolbit, ground to the correct profile
+- 1/4, 3/8 and 1/2 collets. Used to hold end mills, fly cutters, and the small boring head
+- 2.5" face mill. Needs to be replaced, as all the carbides are chipped, and are not available for purchase. Still works reasonably well
+- Drift keys. USe to remove the tooling from the spindle. See document (pending) for use.
 - (many more in varying condition)
+- (Most) tooling is located in the red toolbox in the end of the (pending) work bench.
 ===== Speeds & Feeds =====
@@ Line 61: / Line 70: @@
 | Vice alined and bolted to table | Nov 26, 2013 | QuanaParker |
 | Tool/Work bench built  {{::tool:grizzly_toolbench_img_3981.jpg?200}} {{::tool:grizzly_toolbench_img_3983.jpg?200}} | Nov 26, 2013 | QuanaParker |
+| New drawbar, drift keys | Feb 2020 | Billiam |