User Tools

Site Tools


tool:green_manual_mill

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
tool:green_manual_mill [2017/01/18 16:12] rsimtool:green_manual_mill [2020/03/16 07:16] billiam
Line 11: Line 11:
 ^ Champion           | See [[tool:compendium_of_champions#tools|Compendium of Champions]]     | ^ Champion           | See [[tool:compendium_of_champions#tools|Compendium of Champions]]     |
  
-{{ ::green-manual-mill.jpg?200|}}+{{ ::green-manual-mill.jpg?200| }}
  
 ===== Safety ===== ===== Safety =====
Line 19: Line 19:
 ===== Specifications: Mill ===== ===== Specifications: Mill =====
  
-Mill is a Long Chang LC-15A. No specifications for this mill appear to be available online. The following information was measured from the mill and may be inaccurate.+Mill is a Long Chang LC-15A. Very little info for this mill is available online. 
 +  
 +Please review this {{ :tool:lc15_lc30_manual.pdf | Basic Manual }} 
 + 
 +The following information was measured from the mill and may be inaccurate.
  
 Spindle Taper: Measured ~3.215in long, 0.8in minor diameter, 0.95in major diameter. Very close to Morse #3 Spindle Taper: Measured ~3.215in long, 0.8in minor diameter, 0.95in major diameter. Very close to Morse #3
Line 37: Line 41:
 ===== Fixtures ===== ===== Fixtures =====
  
-We have a drilling vise intended for use with this mill that clamps to the mill table.+The 3.5" swivel vise can be bolted to the table via T nuts / bolts. Never assume that the vise is aligned correctly; use a dial indicator to check.
  
 We have a set of 1/2in T nuts + fingers + step blocks for the CNC mill that will also fit this mill. We have a set of 1/2in T nuts + fingers + step blocks for the CNC mill that will also fit this mill.
Line 43: Line 47:
 ===== Tooling ===== ===== Tooling =====
    
-- Drill Chuck+- Drill Chuck - at the moment, the only chuck key that fits is on the drill press in the Fab shop area. 
 +- 2x Offset boring heads 
 +- Fly cutter. Takes an HSS toolbit, ground to the correct profile 
 +- 1/4, 3/8 and 1/2 collets. Used to hold end mills, fly cutters, and the small boring head 
 +- 2.5" face mill. Needs to be replaced, as all the carbides are chipped, and are not available for purchase. Still  
 +  works reasonably well 
 +- Drift keys. USe to remove the tooling from the spindle. See document (pending) for use.  
 - (many more in varying condition) - (many more in varying condition)
  
Line 61: Line 71:
 | Vice alined and bolted to table | Nov 26, 2013 | QuanaParker | | Vice alined and bolted to table | Nov 26, 2013 | QuanaParker |
 | Tool/Work bench built  {{::tool:grizzly_toolbench_img_3981.jpg?200}} {{::tool:grizzly_toolbench_img_3983.jpg?200}} | Nov 26, 2013 | QuanaParker | | Tool/Work bench built  {{::tool:grizzly_toolbench_img_3981.jpg?200}} {{::tool:grizzly_toolbench_img_3983.jpg?200}} | Nov 26, 2013 | QuanaParker |
 +| New drawbar, drift keys | Feb 2020 | Billiam |
tool/green_manual_mill.txt · Last modified: 2023/02/09 20:43 by androidlx

Except where otherwise noted, content on this wiki is licensed under the following license: Public Domain
Public Domain Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki